![]() ![]() When the accurate placement of a heavier load is needed, a geared trolley is the best choice. They will support a chain block with a top hook or lug mounted suspension and are preferred if you’re going to be lifting lighter loads. Push trolleys are designed to operate manually and horizontally on a flat or tapered beam by using the bottom flange and a set of wheels. The decision of what type of trolley to pick should be based on a few key elements: PUSH TROLLEYS SELECTING A TRAVEL TROLLEYīeam travel trolleys are available in a variety of different types with different options- electric or manual,push or pull, and different beam widths. The jaw locking lever secures the clamp in place when positioned on the girder’s Horizontal flange and can be lifted and rotated. ![]() ![]() Just like the TTG, these clamps can be used just one at a time, although they should be used in pairs along with a spreader beam if the girder is long.Īvailable in capacities of 1000kg and 2000kgĬG girder clamps are used for lifting and rotating girders through 90 degrees.Ī single clamp can be used unless the girder is long, then two clamps on a spreader beam should be used. The jaw locking lever secures the clamp in place when positioned on the girder’s vertical flange. The TTR girder clamp differs from the previous one by being able to transport girders in the horizontal position, also ideal for use within steel stockholders. These clamps can be used just one at a time, although they should be used in pairs along with a spreader beam if the girder is long.Ĭamlok TTR Vertical Flange Girder Vertical Stacking ClampĪvailable in capacities of 750kg up to 3000kg The jaw locking lever secures the clamp in place when positioned on the girder’s horizontal flange. The TTG girder clamp is for transporting girders in the vertical position and is ideal for use within steel stockholders. The Yale SC92 beam clamp is the same as the YC5 with the exception that it comes complete with painted steel shackles.Ĭamlok TTG Girder Horizontal Flange Stacking ClampĪvailable in capacities of 500kg up to 7500kg It comes complete with a locking device and the threaded spindle allows an easy attachment and secure grip to the beam flange.Īvailable in capacities of 1000kg up to 20,000kg Yale YC5 Beam Clamps are a quick, easy and effective rigging point for lifting equipment. COMPARE CLAMPSĪvailable in capacities of 1000kg up to 10,000kg Most beam clamps are developed for use as a suspension point for a hoist and not for attachment onto a load that is being lifted. Use clamps or any other lifting equipment made for other uses.įorce a clamp onto an unsuitable beam or hoist. Test the operation safely and that the brakes are working, the path is clear, and the area is prepared. If using a hoist, check that the chain is not twisted that the hook is hanging directly above the load. Make sure that the beam/girder width is suitable for clamp and that the clamp is centered over the load. Inspect beam clamps before handling, using and storing.Ĭheck that the supporting beam must be undamaged, not warped, and suited to the weight of the load and equipment used. Some Dos and Don'ts to ensure the longevity of your clamp and personal safety: Some variations of clamps are used to lift, stack, and position girders while others must not be used for lifting and are instead used as a suspension point on a beam for a hoist.Ī beam clamp is used to attach lifting equipment, such as a hoist or chain block, to a suitable beam or gantry which is fit for purpose and that can have compatible capacities.Īvailable in a variety of capacities and functions, they are made to suit different beam sizes, can be adjustable, and can be suitable for temporary or permanent uses. WHAT’S THE DIFFERENCE BETWEEN A BEAM AND A GIRDER CLAMP? In this post I will go through everything about the main devices for using with a chain block or electric chain hoist of any kind: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |